25 May 2013

MF station setup at PA3ABK

Just a small overview of the MF antenna and MF transmitter.

The antenna picture gives you an idea. Click for enlargement. In total 54m of wire is used. The topwires are not connected together but it's one wire which goes back and forth. Read this item to learn the background.  Both roofpoles have a length of 5m, and distance is 7,5m. The backyardpole is 10m.
Besides the "waterworks" earth, there is also an  "earthprobe" in the garden, 3m pipe driven into the soil. For reception I use the garden counterpoise which has less "noise". A reed switch arrangement takes care of switching the correct "earth"


The whole trick isn't the antenna itself but the earth system.
Having a garden with only 12m space doesn't leave much left for a decent radial system. My house is part of a terrace arrangement. Every house has his own "earthprobe"All these earthprobes are connected together, Over the whole range of 100m  I have a firm counterpoise. Needless to say that other cables, pipes of all kind of services are connected to it. In the Netherlands all cables pipes in teh city are buried.
The toppart  of the antenna poles holding the arrangement are of glass fiber. This is important to avoid that radiation is not absorbed.
The system is tuned by a "large" variometer ex merchant transmitter S-1250, which is capable to handle over 600W. The impedance matching is done by a core 3C65 material. Primary 15 windings litze secondary is a flexible wire of  5. It's easy to increase or decrease the windings by simply  adding more or less turns thru the core. The system seems to have a total impedance of 7 Ohms, which is rather low for this given situation. Most amateurs in this environment have around 50 Ohms. The variometer is placed as close a possible to the window. A feedthru arrangement of a few centimeters is done to keep leakage a as low as possible. The wiring is leaving the house almost horizontal. This maintained by a horizontal glass fibre holder. Connection to "earth" is done  by "disposed, old" fat coax cable in order to keep the skin-effect as low as possible.
Another advantage of my location is the lack of high trees which give me a reasonable  free take-off.

The system has a basic resonance of 1430kHz. I also use it for 160, 80, 60 and 40m. Other bands are covered with a  ladderline feeded 2x 7,5m Inverted V. Which is also visible on the picture above. Note that this antenna must be "isolated" when using the 630m otherwise it will suck a lot of energy to the ground.
Below is sketch of the whole technical setup. It is not updated to the present situation.


WSPR is produced with a MP3 player and a timer. The shift has been multiplied by 4 and was created with Audicity. This to survive de DIV/4 sequence of the GW3UEP PA. Details can be found here.
To avoid "hiss" during silent periods, there is a squelch to make sure that the drive has reached a certain level. Without it, the PA will behave erratic, transmitting broadband noise.

23 May 2013

Back to basic... The Marconi antenna

One of the nice side effects of working on 630m, is the aim to make use of your transmitter power in a most efficient way. Especially when the antenna footprint is small. The main principle on this band is to get as much copper as high as possible. In NL the antenna height is restricted. It's 5m above the rooftop. If you want to go higher a permit of the local authorities should be obtained. Well I opted not to apply for "higher" for several reasons.

My first steps on MF were made a G5RV antenna, a single wire spanning over the house. The feeder was joined together and tuned as T-antenna against the waterworks. This wil work, but not for everyone. I use the houseprobe as "earth" and lucky enough this seemed to be a very good one for MF.
A long list a several antenna variations followed.
It's clear that when you fatten the top the efficiency will increase.
Now I came back to basic... The Marconi T-antenna, however a variation of it.
I was inspired by the Dutch offshore radio station Radio Veronica, running 10kW on 557kHz. In the 70's I happen to be on board a vessel crossing the Pacific.
Satcom was not common in those days and traffic was cleared by HF. Best time was around 1600-2000 UTC from that location to work EU. Time difference forced me to do this very early in the morning, just before sunrise.
After finishing traffic a had a chat with the 1st mate, having a Grundig YachtBoy in the bridgeporthole producing quite good music.  The stationcall revealed that it was Radio Veronica... I went back to the radioroom and tuned the main aerial to the Veronica's frequency this was done with tuner of the aux MF (500kHz) tx. The 1st mate was very pleased the portable could now used also in his cabin. This event repeated itself for some days, until we sailed out of this propagation "tunnel".

The antenna Veronica used, was relative very small. It's design came from a Belgium antenna expert. A meandered T-antenna.
Have look at the website of Radio Veronica. It's in Dutch, apart from a lot of nostalgia, it contains technical information. Seawater was certainly in their advantage, nevertheless a remarkable job covering the Netherlands with only 10kW.

I  tried to arranged something similar, only not with 4 but with 3 wires and the length, only 7,5m.
I can extend this to my backyard, but constructionwise I have my limitations.

The transmitter and tuner is on the 3rd floor. A "fat" earthcable is run from the tuner to the houseprobe. From the tuner the antenna wire is run 12m into the backyard picked up by a pole at about 8m. Than 2m straight upwards.
This 2m spacing is necessary to avoid de-tuning during "windy" periods.
The wire returns to the house and picked up by a pole about 5m above the roof. From there 7,5m straight to the front of the house. Also picked up by a 5m pole. On both poles there is horizontal alu pipe of 60cm, just 20cm below the upper wire. The wire is going back and forth between those poles. If you add up the total wirelength is 53,5m.